(813) 322-5002 Serving all of Pasco County Licensed & Insured · FL CFC1431903

Guide

How Slab Leaks Are Repaired

You already think the leak is under the floor. What happens next is one of three repairs. Which one depends on where the break is, what the pipe is made of, and whether this is the first time it has failed.

Slab leaksReroutingRepiping

Locating it before anything gets opened

Every slab repair starts the same way. We find the break and mark it on the floor. Nothing gets cut until that is done.

Water under a slab travels along the pipe trench and the fill, so the wet spot or the warm patch is often not over the leak. A pressure test on the hot and cold sides separately tells us which line failed. Acoustic listening picks up the sound of pressurized water escaping through the concrete. Thermal imaging shows the heat plume from a hot line. Tracer gas covers the slow weeps and plastic lines the others struggle with.

The point of all of it is one opening instead of several. The pipe fitting is the small part of a slab repair. The saw cutting, digging, concrete and flooring are the big part, and every wrong guess means doing them again.

Locating also tells us what the pipe looks like at the break and how the line runs through the house. That is what the choice between the three repairs gets made on.

Spot repair: opening the slab at the break

The floor covering comes up over the marked spot. The concrete is saw cut into a square, broken out and removed, and the sand underneath is dug out by hand down to the pipe. The damaged section is cut out and a new piece joined in. The line is pressure tested with the hole still open, so the repair can be seen holding before anything goes back.

Then the trench is backfilled and compacted, and new concrete is poured level with the slab. It has to cure before tile or flooring goes back over it. Until then you have a patch of bare concrete in the middle of the room, kept clear of foot traffic.

Inside, expect dust. Saw cutting concrete indoors is messy even with water on the blade and plastic hung around the work. Furniture and anything on the floor near the spot has to move. If the break is under a cabinet, a tub or a wall, the opening may have to be made from the side, which makes it bigger.

The water to the house is off while the pipe is cut and joined. It goes back on once the repair holds. The concrete and the flooring take the time, not the plumbing. Ask up front who is putting the flooring back. Matching tile that is twenty years old is not always possible, and that is worth knowing before the floor is cut.

Rerouting: abandoning the bad section

A reroute leaves the failed line in the slab and takes it out of service. A new line is run from a point above the floor, up through a wall, across the attic and back down to whatever the old one was feeding. The section under the concrete is capped at both ends and abandoned.

The floor is not opened at all. The work happens in the attic and inside walls. What you see afterward is a few patched openings in drywall where the new line drops down, usually in a closet, behind an appliance or near the fixture it serves. Settle who patches and paints that drywall before the work starts.

The new line is run while the old one is still in service, so the water is only off for the tie-ins at each end. On most jobs that is the shortest water outage of the three options.

A reroute is the usual answer when the break is somewhere that makes a spot repair expensive or destructive — under a tub, under cabinets, in the middle of a large tiled floor — and when the line is short enough and the attic access good enough to make the run practical. It is also the answer when there is good reason to think this line will leak again.

A spot repair fixes one hole in an old pipe. A reroute takes that pipe out of the picture.

Repiping the affected run

Sometimes the problem is not one line. The leak may be in a pipe that is the same age and material as everything else under the slab, in a house that has already leaked in other places. Then the honest question is whether to repipe the run or the whole house instead of chasing failures one at a time.

A repipe works the same way as a reroute, just more of it. New supply lines go through the attic and drop inside the walls to every fixture they serve. The old lines under the slab are abandoned. Nothing comes up through the floor.

The water is off for stretches during the working day and usually back on overnight. People stay in their houses through a repipe routinely. How many days it takes depends on the size of the house, the number of fixtures and what the attic is like. We do not name a number of days before we have walked it.

It is permitted work, inspected by the county. Pipe Perfect LLC is a Florida Certified Plumbing Contractor, license CFC1431903, and permits are pulled under that license. We are a plumbing contractor. We do not perform or sign home inspections, four-point inspections or anything else that requires a license we do not hold.

Which situation points to which

A spot repair makes sense when the pipe is sound apart from the break. A nail, a rock that rubbed through the line, a single bad joint, or a first failure in a line that looks sound once it is exposed. One cause, one hole, one repair.

A reroute makes sense when the break is somewhere costly to reach, or when the pipe itself is the problem. Old copper under a slab corrodes from the outside, where it sits against damp sand. Once a pinhole opens, the rest of that line has been sitting in the same conditions for the same number of years. Galvanized steel corrodes from the inside and closes up as it goes. With either one, the first leak shows what the pipe is doing. It is not a one-off.

That is the argument against patching the same slab twice. When an old copper or galvanized line has just leaked, the next leak is likely to be on the same line, and it may be a few feet from the first one. A spot repair means opening the floor now and possibly again later. A reroute means opening drywall once and never going back under that floor for that line.

A repipe makes sense when the pattern covers the whole house, not one line. That looks like leaks on different runs, in different rooms, close together in time, along with discolored water or pressure dropping everywhere at once. Keep a dated record of every leak and where it was. That list is what the decision gets made on, and it is the first thing we ask for.

Straight answers

Common questions

Do you have to break up my floor to fix a slab leak?

Only for a spot repair, and then only at the spot that was located. A reroute or a repipe takes the failed line out of service and runs new pipe through the walls and attic instead, so the floor is not opened at all. Which one makes sense depends on where the break is and what condition the pipe is in. We tell you after we have located it.

Is rerouting better than a spot repair?

Not always. On a line that is otherwise sound, with one clear cause for the break, a spot repair is a reasonable fix. On an old copper or galvanized line that has started to pinhole, a reroute is usually the better answer. The next leak is likely to come from the same line, and a spot repair leaves you under the slab again.

How long will I be without water?

For a spot repair, while the pipe is cut and joined. It goes back on before the concrete is poured. For a reroute, only while the new line is tied in at each end. For a repipe, in stretches during the working day, with water back on most nights. If the leak is on the hot side, closing the cold supply to the water heater usually keeps cold water running in the house until the repair.

Will insurance pay for the slab leak repair?

That is between you and your carrier, and we do not know what your policy says. Many policies treat the pipe, the cost of getting to it and the water damage it caused as separate things. Photograph everything, dated, before anyone touches it, and keep the record of where the leak was located. We document what we find so you have something to hand an adjuster, but we cannot tell you what they will decide.

Where to go next

What we actually do

01

Slab Leak Repair

Hot spots on the floor, an unexplained spike in the water bill, the sound of running water with fixtures off, and cracking near a slab edge.

View
02

Leak Detection & Repair

Unexplained water bills, damp flooring or drywall, running-water sounds with everything off, and slow leaks behind walls or under slabs.

View
03

Whole-Home Repiping

Aging galvanized or polybutylene supply lines, repeated pinhole leaks, low water pressure, and discolored water from corroding pipe.

View